BSOD :: Read / Analyze This Dump File So Know The Cause
Jan 20, 2016
I built a pc last week and I get the BSOD after a few minutes of playing any game I try. I only have the last dump file I got because the BSOD before the last wouldn't let me start my pc in safe mode or restore to a previous date so I had to reinstall windows 10. Here is my dump file, I know how to open it but I don't know how to analyze it and figure out what is causing the BSOD here is my build shadybk - Saved Part Lists - PCPartPicker
View 9 Replies
Similar Messages:
Sep 11, 2015
Windows 10 created a new crashdump file called ShellExperienceHost.exe.3708 in my AppData/local/Crashdumps folder, how to read one of these dump files or what this one means to me?
View 9 Replies
Nov 24, 2015
I wasn't quick enough to note down the full error as Windows did a crash dump, but I did notice the offending file was an Atheros driver. This was confirmed by Control Panel | Reliability Monitor
Source
Windows
Summary
Shut down unexpectedly
Date
24/11/2015 10:35
Status
Report sent
[Code] ....
I've used the DM Log Collector to get the DMP file, but I'd quite like to study it myself, and send relevant parts to Alfa (who make the offending Wi-Fi adaptor with the Atheros chipset).
View 3 Replies
Jan 14, 2016
I have a fresh install of Windows 10 Home on a factory built PC (Chillblast) that was running OK under Windows 7, but is now Blue Screening on Windows 10.When I boot the PC from cold about 1/3 of the time it will blue screen. The messages vary. Sometimes it will say IRQL Not less or Equal, or Page fault in non-paged area, or Memory Management.
The messages always happen pretty much at the exact second that you would normally get the logon box up. It never Blue screens when I'm actually using the computer, even if I'm hitting it hard with games. It also never blue screens on a reboot. Only when it's booting from power complete power down.I suspect that it's software rather than hardware, maybe a driver?
The only message in the logs is that the computer as recovered from an unexpected shutdown. It rarely creates Dump rile.I thought that it might be bad RAM. I have two 8GB chips. Both are the original chips that the computer was sold with. If I try with one chip in it runs perfectly. It doesn't matter which chip, or which slot the chip is in. It runs perfectly with all combinations. If I put them both in 1/3 of the time BSOD.
I've run Memtest86+ and it didn't find any problems. I've also run the System File Checker and it didn't find anything.As this is a fresh install I don't have much loaded. It started blue screening with only the basic software needed to run my hardware, and an Anti-Virus (Avira) loaded.
Windows 10 is installed on a totally new disc, straight out of the box (Sandisk SSD).Other than the hard disk and a soundcard, the PC is pretty much a factory build, with a factory configured motherboard. It's not overclocked, and I haven't tinkered with it.Before I installed Windows 10, I occasionally had a Stop 0X000008a error, but I don't know if that's relevant or not as it was a different OS on a different hard disk.
View 9 Replies
Oct 29, 2015
I am running Windows 10 (64-bit), but this problem also occurred on 8.1 and 7 (both 64-bit) with clean installations. I am also dual booting Ubuntu Studio 15.04, but more on that later.
When I boot my PC into 10, I have up to ten minutes before my PC either resets forcefully by itself, or freezes and never recovers. When I check the Minidump folder afterwards nothing is there.
I have replaced both my CPU (amd fx-6300) and PSU (corsair cx500m), and tested my RAM (with both sticks or just one), but none of that has fixed the problem.
My BIOS settings are at their defaults, no over/underclocking or over/undervolting at all.
The odd thing is, Ubuntu Studio runs fine with no crashes as far as I can see *EDIT: NOT THE CASE* , but if there was a software problem surely there would be a dump file?
View 2 Replies
Nov 23, 2015
I have recently had a crash dump file appear in c:windowsminidump.
I am uploading it here, for those who may wish to review it. However, I cannot specify what the cause of this problem may have been.
View 3 Replies
Feb 10, 2016
I would get a black screen for a few moments, before the computer just restarts. No BSOD, no screen tearing or strange noises from the case, no indication whatsoever that it was about to restart. So I started trying to figure out what was wrong. Using Bluescreenviewer and WhoCrashed? I found out that it was a 0x124 error citing the ntoskrnl at fault. Reading online, it seemed that this was generally caused by either a thermal issue, hardware problem or in some cases driver problems.
I started updating everything I could. Graphics drivers, mouse drivers, keyboard drivers, BIOS drivers, etc. Still got the restarts. They seemed to be appearing only when I was playing games (don't use this particular PC for much else, so took a while to realize), so I decided to check thermal issues. Using MSI Afterburner and CPU-Z, I found that my CPU was never reaching any significant heat (my Hyper 212 EVO keeps it under or around 40C even under heavy load), and that while my graphics card got hot, it never went beyond 70, so it didn't seem to be a thermal issue there.I ran memtest86 to try to identify ram issues, and it came back, after a night of running, clean. I did a dskcheck /r, and while it took a bit of time, it too came back alright. In order to truly rule out driver issues, i reinstalled windows 10, and still it kept happening.
I read online that there was a chance that the power supply could be acting up. Since I had been meaning to update my graphics card, and needed a new power supply to go with it, I decided to do that. I plugged in my new PSU, and my new GPU, and it went fine for about a day or two before the restarting resumed. I tried playing with the case side open, to truly rule out cooling issues, and it still restarted. I moved the computer, and plugged it straight into the wall because I had a suspicion that maybe the extra cable wasn't giving it enough juice, but it still restarted.
I'm now at my wits end. I've tried everything I can think of. My new GPU never goes to high temps, my CPU seems to be running fine, I haven't found any ram memory problems, my new PSU can't be to blame, and so I don't know whats left.
Tl;dr
Restarts started after some inactive time. Seems to be a 0x124 bsod error
Tried the following:
-update all drivers
-update BIOS
-re-roll to previous versions of graphics drivers
-re-install windows 10
-purchase new PSU and GPU
-memtest86 came back ok
-dskcheck /r came back ok
-tried playing with side off
MSI never shows the CPU or GPU going into any dangerous territory in terms of temps.
View 9 Replies
Sep 5, 2015
On my system, I have Automatically Restart set in the system failure but when it BSOD's, it says that the system will restart after the dump but it appears it just stays at the blue screen without restarting even after an hour on atleast 3 occasions since I've upgraded to Win10 from Win7 Home Premium on August 11, 2015, the system is able to restart and shutdown normally.
View 9 Replies
Jan 14, 2016
When I try to dump the stack I input the command dps ffffd00026876000 ffffd00026870000. The two values are my base and limit values. I tripple checked them many times.
However everytime I input that command I get an error message saying
"^ Range error in 'dps ffffd00021787000 ffffd00021781000"...
View 1 Replies
Oct 13, 2015
I have been fighting with my computer for about four weeks now, and I am not getting anywhere. In a nutshell, my computer started to randomly shut down and seldom reboot. There are no specific patterns I notice, except that when I try to find out what's going on the random reboots/shut downs happen more frequently (3-5 time per hour). When I just use the computer, it lasts longer without any issues. I may get between 1-4 hours. No BSOD and no error.
Now when the computer shuts down, it is a hard shut down. It is as if I turned off the power button from the PSU itself and turned it back because when I turn the computer back on, it turns on briefly and shuts down again, turns on again, beeps the all things okay beep, and boots to window. It is worth noting that this behavior started happening without adding any new hardware, software, or driver.
Here's what I have done so far to try to ameliorate/diagnose the issue.
1) I reset the PC - Here's my post on that issue if you want to take a look.
2) I did a clean install - (truly clean install).
3) I boot into the Bios, and it stills reboot/shut down (this causes me to suspect a hardware issue, but what?).
4) I open the case and ensure that everything is properly seated on the MOBO.
5) I cleaned out the PC of dust
6) My temperatures are normal, no overheating going on.
7) I ran ad-ware/spyware check - nothing has been found.
8) I ran a virus check (yes, with windows defender) - nothing came up. I don't think it's a virus since the problem continues even after a clean install.
9) It's not a lack of power issue. My PSU is 1000W and I am not using that much power.
10) I did a stress test for over an hour, and everything was normal (this causes me to doubt it is a hardware problem).
11) I am sure I have done more than the before mentioned steps, but I can't remember them all.
At this point, I suspect my issue might be hardware related; however, I really do not know what this could be, and I do not want to start buying new hardwares (i.e. PSU) without knowing what the issue really is, particularly when it endured a stress test without any issues. I thought of applying a thermal paste/grease on the CPU, but since I am not overheating I don't think that's necessary. So, I am at a lost on what my next steps should be. I am not savvy enough on reading memory dumps files... my computer is not generating any of those files anyway. But I know I can force my computer to generate them.
View 9 Replies
Sep 12, 2015
Upgraded from Windows 8.1 Pro to 10 Pro. I think I took care of the update bug so I don't believe it is the issue.
Updated GForce Drivers after using DisplayDriverUninstaller.
SSD C: Drive firmware updated.
Ran Memtest86+ on each stick for 8 passes with no errors.
Updated audio drivers.
Updated network drivers.
Updated SATA drivers.
Ran Windows Defender Full Scan with no findings.
Ran Malwarebytes Full Scan with no findings.
It happens when I play games. I ran one 3DMark test with no issues. Ran it again and it reset as it normally does. I ran Furmark for 5 mins with no issue.
View 9 Replies
Feb 10, 2016
I've a Dell XPS 15 9550 (512GB SSD PCIe) that gives me a BSOD after at least two hours of uptime. It doesn't create any dump, it only gives me the error on the BSOD critical_process_died. I alredy tried to do various clean install of the OS redownloaded a lot of times and to set from BIOS the drive to RAID in AHCI with various manually installed driver without any result.. I don't know what can I do anymore..
View 2 Replies
Jan 26, 2016
Since using XP and then Windows 7 have always set the Hosts file to read only as a security measure.Is it still advisable to do this on Windows 10?
View 4 Replies
Oct 10, 2015
Windows 10 email opens fine and all my email accounts appear correctly, but when I open an account to read mail, the program crashes when I try to delete an item or move to the next item. I have to reopen the program and start again.
View 1 Replies
Oct 1, 2015
A few days ago, i recorded something with "vlc media player". Now i wanted to delete this file, but when i press the Delete Button, nothing happens. If i want to rename it, the Explorer crashes. If i click right and choose "delete" nothing happens. No "fail-message", nothing.
View 1 Replies
Dec 11, 2015
BSOD problems. They occur during general use like web browsing, file management, and at any time really.
Here is a zip of what I was told to upload.
DESKTOP-38MB8BC-Fri_12_11_2015_173625_85.zip
View 1 Replies
Feb 10, 2016
My system has been running fine on windows 10 for a couple of months now, but recently i started getting BSODS without installing new hardware. The BSOD Error is page file in nonpaged area.
I tried taking a look on the dump files myself, I couldn't solve it but this is what I did/found out. The error seems to be BCMWL63A.sys I tried reinstalling my WLAN driver, still bsod (my wlan adapter:asus pce-ac68 ac1900)
The latest dump log is from driver verifier...
View 2 Replies
Dec 15, 2015
New Skylake based build with Windows 10 Pro on a 250GB Samsung SSD. After initial startup I decided to format the drive to repartition it and did a clean install of Win10. Shortly after, the wireless connection to the router kept failing every few minutes and I would have to repair it. Then suddenly for no reason I could find I couldn't open the control panel. Clicking the taskbar icon would cause the screen to blink and all the taskbar icons would disappear and reappear. Decided to do a reset and that seemed to work until suddenly, again without warning or reason, I couldn't open the File Explorer and it did the same thing the Control Panel did and couldn't find a way to repair it.
Booted up from the Win10 install USB device and did another clean install of Win10. Got all of my programs reinstalled and running and all was well so I quickly did a system and partition backup with Todo. The wireless connection was working but suddenly I once again couldn't open the control panel. I had installed all Windows updates after doing the backups including the new version update but I don't know if there was anything in there that might have triggered the control panel issue. I booted up with the Todo emergency boot disc and did a partition restore. Everything is once again functional and I'm delaying running any Windows updates. Ran NOD32 virus scans and SFC /SCANNOW and neither found any problems or issues.
I'm just cruising along at the moment waiting for another incidence to occur. Is it possible I have a flaky SSD? Windows 10 seems to have a few issues with SSDs such as showing two instances of the same drive in File Explorer.
View 2 Replies
Feb 23, 2016
I have downloaded the zip file and after extracting to one of my folders, I am sending the whole folder.
My computer makes humming noise before crashing to a blue screen.
I am very much fed up and am thinking to go back to Win 7 Pro.
View 6 Replies
Dec 11, 2015
I have w10 on both pc and phone. How can i read sms via pc? The app dont show them, should i use cortana? How?
View 9 Replies
Aug 10, 2015
After updating to Windows 10 I created a homegroup and now everything in documents is stuck in read only. It's the filled in box not the checked box. I manually uncheck the read only and it goes right back to read only. I left home group and tried unsharing folders but no luck. I'm at a loss in what else to try. Also tried rollback and it fails. Tried reset and it fails. Tried image rollback and fails.
View 3 Replies
Aug 21, 2015
Since I have upgraded to Windows 10 Pro, I noticed that all my folders' attributes are read only . Even if I create new folders, they are read only on creation. When I try to remove the read only attribute in the folder properties, it looks like it's removed, but when I check it again, it shows that it's read only. I tried other methods, like diskpart, and tried to take ownership of the folders
Is there any way to fix this problem? I can create new files and modify existing files in the folders without any problem, but it's really annoying, for example Steam says it can't install games and updates, because the folder what I choose to install games is in read only mode, the only solution is to run it as an administrator. I need to run almost every program as an admin, to make them usable, or they report problems with read only folders. The OS itself is up to date.
View 6 Replies
Sep 1, 2015
I have recently installed Windows 10 on my desktop. I now find that most of my files are "read only" I have tried to deactivate this in properties for the various folders but it does not work. Other than trying to copy every file that is currently in use?
View 1 Replies
Aug 20, 2015
I have been using Windows 7 and all my JPEGs worked fine. Upgraded to Windows 10 and about 1/2 of all my JPEGs can't be read by ANY programs. I get the message "Not a valid JPEG-JFIF File".
View 4 Replies
Aug 25, 2015
Just upgrading to Win 10 and noticed this morning that I am unable to change the settings from Read Only to allow all saved work. I have tried changing the Preferences, but as soon as I do, Apply, Ok and the settings refer back to Read Only. I haven't noticed this on any documents,only on Pictures. I have tried changing the directory and Pictures, but no luck.
View 5 Replies
Aug 4, 2015
I cant make a folder to full access. It remains as READ only always, when I try to unmark the square mark. Its like there in all of my files and folders. Do anything special to do to make them full access other than unmarking read only ?
View 9 Replies
